2010 Blazer Bay 1960 performance, feel, pros, and cons.

Discussion of Blazer's line of Bay boats.

Re: 2010 Blazer Bay 1960 performance, feel, pros, and cons.

Postby fisheye48 » Wed Feb 10, 2010 2:16 pm

what picture are you talking about???
fisheye48
 
Posts: 56
Joined: Sat Jun 06, 2009 2:10 pm

Re: 2010 Blazer Bay 1960 performance, feel, pros, and cons.

Postby blazer butch » Wed Feb 10, 2010 2:19 pm

sorry if yall think i was arguing, i was trying to help tedwards out, unfortuantly with the industery so far down i am not there any more to handle these type issues. maybe the marine buisiness will pick up soon and i can go back and continue building a great product. just trying to help with a few issues.
blazer butch
 
Posts: 76
Joined: Tue Jul 22, 2008 8:25 am

Re: 2010 Blazer Bay 1960 performance, feel, pros, and cons.

Postby tedwards » Wed Feb 10, 2010 2:23 pm

when you go to Blazerboats.com then click Bay Boats then click 1960. you will see an inside of boat picture and you can see the pole racks on each side of the hull (inside). I would like to mount some like this in my boat but i don't want to drill hole through the hull.
tedwards
 
Posts: 16
Joined: Sat Feb 06, 2010 8:54 am

Re: 2010 Blazer Bay 1960 performance, feel, pros, and cons.

Postby tedwards » Wed Feb 10, 2010 2:25 pm

blazer butch wrote:sorry if yall think i was arguing, i was trying to help tedwards out, unfortuantly with the industery so far down i am not there any more to handle these type issues. maybe the marine buisiness will pick up soon and i can go back and continue building a great product. just trying to help with a few issues.



I did not take it as arguing. I thank you for your input. and again I LOVE MY BOAT. Not the seat :)
tedwards
 
Posts: 16
Joined: Sat Feb 06, 2010 8:54 am

Re: 2010 Blazer Bay 1960 performance, feel, pros, and cons.

Postby blazer butch » Wed Feb 10, 2010 2:30 pm

use a 3/4 inch screw and 5200 marine sealant you will be fine, there is a small space between the inner aand outter liner
blazer butch
 
Posts: 76
Joined: Tue Jul 22, 2008 8:25 am

Re: 2010 Blazer Bay 1960 performance, feel, pros, and cons.

Postby rorgero » Wed Feb 10, 2010 4:26 pm

butch, when screwing through the deck or inner surfaces of the boat should I pre drill a hole first before screwing a screw? :?:Or is it safe to screw into the glass without a pre drilled hole.
rorgero
 
Posts: 62
Joined: Thu Jan 03, 2008 8:58 am

Re: 2010 Blazer Bay 1960 performance, feel, pros, and cons.

Postby blazer butch » Wed Feb 10, 2010 10:05 pm

it is defenatly safer to pre drill the hole, this will stop any cracking of the gel coat, after you drill pilot hole take your screw driver bit and kinda round the outer edges of the hole, this will eliminate cracks in the future.
blazer butch
 
Posts: 76
Joined: Tue Jul 22, 2008 8:25 am

Previous

Return to Bay Boats

Who is online

Users browsing this forum: No registered users and 1 guest